Provision-ISR PZ-22IR Manual do Utilizador

9 The Main menu as follows: 4.3 SYSTEM Menu: <Main Menu>  <SYSTEM> SITE INFO DISPLAY SETUP BOOTUP SCREEN PASSWORD SET

10 System info includes following settings.  < SITE INFO>: In this menu the user can setup the dome’s name, View the Hardware address, change

11 <Main Menu>  <SYSTEM>  <SITE INFO >  <NAME>: The title name of the dome. Assigning a name to a dome helps the user

12 4.3.2 DISPLAY SET UP < Main Menu><SYSTEM><DISPLAY SETUP>  <SITE NAME>：Choose to display site name or not.  <PRE

13 4.3.3 DISPLAY BOOT-UP INFO <Main Menu><SYSTEM><DISPLAY BOOT-UP INFO> Enter into Boot-up info displays to check current setup,

14 password. If the old Password input is not correct, you will not be able to change the password.  <CONFIRM>: Re-input the new password and

15 Use left and right keys to move the cursor to desired item, use up and down keys to change the current cursor value. 4.3.8 RTC RIME RUNNING <

16  <ZOOM SPEED>: Set the zoom speed level to HIGH or LOW  <DIGITAL ZOOM>: Turn On/Off the Digital Zoom.  <JOYSTICK AF/AI>: S

17  <CAMERA P/N>: Show the current camera P/N (PAL/ NTSC), The PTZ can automatically detected some of the camera Signal mode. If not, please

18 dark. The dome can auto adjust the brightness of the whole image according to the brightness of the center point. Thus backlight compensation can

1 Package Contents: Item Qty. Z-2 2/2 7 IR PTZ 1 Wall Bracket 1 Hinge Pin 1 Rubber Seal 1 DC12V/5A power supply 4 Wall Screws 4 PM8*25 socke

19 DSP Settings: FOCUS AUTO ID DISPLAY OFF CAM ID 1 PROTOCOL VISCA BAUD RATE 9600 485 CONTROL NORMAL LED 1 8 LED 2 1

20  <SHUTTER>: Choosing between Auto and Manual  <WB MODE >: White Balance is normally compensated for by the automatic white balanc

21 4.6 PAN/TILT <Main Menu><PAN/TILT>  <AUTO STOP TIME>: For some particular protocols, the dome will not stop moving even th

22  <SET NORTH>: User can set orientation by using joystick to position north. When select <SET NORTH>, following menu will pop-up. Ad

23 4.7.1 PRESET <Main Menu><AUTO RUNNING><PRESET> In this function, the values of the pan/tilt positions will be stored in the d

24 Move to the desired position and zoom to a suitable level, call preset 1 to save the current preset and return.  < REMOVE CURRENT>: Delet

25 There are three group numbers, the left side is preset number, the right side is dwell time; tour from left to right, up to down in the order to

26 There are max 4 patterns, and the dome camera can record all regular operation in 3 minutes at least. The command will drive the speed dome runs a

27 <360° SCAN DWELL>: [0S]: 360 continuous scan [5S]: 90 intermittent scan, then dwell on 5s, the dome will continuously run at the given rou

28  <TITLE>: To set current zone Name, 16-bit can be set up by the number 0-9 and the letters A-Z of any combination  <LEFT LIMIT>:

2 Table of Contents: 1 General Instructions ... 3 1.1 Safety Instr

29 4.7.6 <PARK TIME> The camera will run certain function automatically if the dome is not receiving any command for the specified time. 0S：P

30 Using up, down, left and right key to adjust the size of the mask, then call preset 1 to confirm and return.  <REMOVE CURRENT MASK>: Re

31 means alarm out on A side, ALoutB means alarm out on B side. Note: The alarm has highest priority. For example, if Cruise set to run at 12:00, and

32 4.11 IR SET <Main Menu>  <IR SET>  <IR MODE >: AUTO/OPEN/CLOSE <AUTO>: Default. When the detected signal value from th

33 APPENDIX I: DIP SWITCH SETTING DIP Switch consists of 8 numbers from 1-8, use 8421 binary cod, max 255 address. When the switch is in

34 35 1 1 0 0 0 1 0 0 36 0 0 1 0 0 1 0 0 37 1 0 1 0 0 1 0 0 38 0 1 1 0 0 1 0 0 39 1 1 1 0 0 1 0 0 40 0 0

35 89 1 0 0 1 1 0 1 0 90 0 1 0 1 1 0 1 0 91 0 0 1 1 1 0 1 0 92 0 0 1 1 1 0 1 0 93 1 0 1 1 1 0 1 0 94 0

36 143 1 1 1 1 0 0 0 1 144 0 0 0 0 1 0 0 1 145 1 0 0 0 1 0 0 1 146 0 1 0 0 1 0 0 1 147 1 1 0 0 1 0 0 1 148

37 197 1 0 1 0 0 0 1 1 198 0 1 1 0 0 0 1 1 199 1 1 1 0 0 0 1 1 200 0 0 0 1 0 0 1 1 201 1 0 0 1 0 0 1 1 202

38 APPENDIX II Shortcuts Key Chart Shortcut Key Function (Set Preset) Set #71 preset Proportional P/T OFF Set #73 preset 0S Park

3 1 General Instructions: 1.1 Safety Instructions:  Make sure to read the user manual before using the product.  Always follow national and loca

39 Shortcut Key Function (Call Preset) Call #71 preset Proportional P/T ON Call #82 preset Start Cruise scan and switch the cruise scan direction

40 APPENDIX III Trouble Shooting Troubles Reason Solution No action when power on 1. The power supply is not connected corre

4 2 Features: 2.1 Product Picture: 2.2 Product Features  Alarm I/O.  Adaptive PELCO-P/D protocol.  Adjustable IR illumination.  Memory recal

5 speed to reduce the dark angle and flashlight effect.  The upper dome adopts 7" aluminum alloy structure for better magnetic shield and he

6 RTC Set any functions at any time IR Light switch Superpower LED：Default: Zoom x1~5: open the near-distance IR lights; Zoom x6~9: open the near-di

7 3.3 DIP Switch Setting: (1)Default Settings: Pelco P/D (auto-detected), baud rate: 2400, address: 1. Use Philips screwdriver to remove the DIP sw

8 4 Setup of the OSD Menu: 4.1 Display Boot-UP Info. Before installation please check the protocol, baud rate, address and RS485 data cable. Default